Weidmuller WI-I/O-9-U2: Wireless Mesh I/O & Gateway User Uživatelský manuál Strana 27
- Strana / 126
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
26
2.5 Connections
2.5.1 Bottom panel connections
Figure 9 – Bottom Panel Connections
Ethernet port
The WI-I/O 9-U2 modules provides a standard RJ-45 Ethernet port compliant to IEEE
802.3 10/100 BaseT. This port provides full access to the module, including
configuration, diagnostics, log file download and firmware upload, of both the local and
remote units.
Additionally the Ethernet port can provide network connectivity for locally connected
third-party devices with Ethernet functionality.
USB Device Port for configuration
The WI-I/O 9-U2 module also provides a USB-device (USB-B) connector. This
connector provides configuration of the device and remote configuration access to other
devices in the radio network.
RS-232 port
The WI-I/O 9-U2 module provides an RS-232 serial port, which supports operation at
data rates up to 230,400 baud. This port supports MODBUS protocol.
The RS-232 port is provided by an RJ-45 connector wired as a DCE according to EIA-
562 Electrical Standard.
RJ-45
Signal
Required
Signal name
Connector
1
RI
Ring Indicator
2
DCD
Data Carrier Detect
3
DTR
Y
Data Terminal Ready
4
GND
Y
Signal Common
5
RXD
Y
Receive Data (from WI-I/O 9-
U2)
6
TXD
Y
Transmit Data (to WI-I/O 9-U2)
7
CTS
Clear to Send
8
RTS
Request to Send
- Industrial Wireless MESH I/O 1
- WI-I/O 9-U2 MESH I/O 1
- 804.794.2877 Main 2
- 804.794.0252 Fax 2
- Industry Canada: 3
- FCC Notice: 4
- Hazardous Location Notices: 5
- IMPORTANT Notice: 6
- TABLE OF CONTENTS 7
- TABLE OF FIGURES 11
- Chapter 1 - Introduction 13
- 1.2 Module Structure 15
- 1.3 Getting Started 16
- Chapter 2 - Installation 17
- 2.2.2 Expansion I/O Supply 19
- 2.2.3 Internal I/O 20
- 2.2.4 Grounding 20
- 2.3 Radio 21
- 2.4 Antenna 22
- Yagi antennas 26
- 2.5 Connections 27
- WI-IO 9-U2 28
- “Factory Boot” switch 29
- USB Host port 29
- Dipswitches 29
- Front panel connections 30
- Figure 16 - Fail-Safe State 33
- 2.5.5 Analog Inputs 34
- Single Ended Voltage Inputs 36
- 2.5.6 Analog Outputs 37
- Chapter 3 - Operation 38
- Digital Inputs 39
- Digital Outputs 39
- ETHERNET 40
- LINK100M 40
- 3.3 System Design 41
- 3.3.4 Design for Failures 42
- Fail-to-transmit alarm 43
- Fail-to-receive alarm 43
- 3.4 WIBMesh 44
- Chapter 4 - Configuration 46
- Figure 23 – Network Settings 47
- Figure 24 - Ping 47
- Figure 26 - IP Gateway Mode 49
- Figure 27 - Default Gateway 49
- Figure 28 -IP Address Range 49
- Figure 29 - Routing Rule 50
- 4.3 Module Configuration 51
- Re-Open Previous Project 52
- 4.3.2 Configuration Screens 53
- 4.3.3 Project Screen 54
- 4.3.4 Adding Units 54
- Unit Details 55
- 4.3.5 Mappings 56
- Write Mapping 57
- Gather Scatter Mapping 57
- Read Mappings 57
- Example configuration 60
- 4.3.7 Address Map 61
- 4.3.9 I/O Configuration 62
- Pulsed Outputs 63
- Analog Inputs 64
- Analog Outputs 65
- Adding modules 65
- (selected on the rotary 66
- 4.3.11 Failsafe Blocks 67
- “Invalid” register state 68
- 4.3.12 Sensitivity Blocks 69
- 4.3.13 Serial Configuration 70
- Serial - Expansion I/O 71
- 4.3.14 Modbus Configuration 72
- Mapping parameters 73
- Modbus TCP Mapping Examples 75
- Modbus RTU Master 75
- Modbus RTU 76
- Master Example 76
- 4.4 Web based Configuration 77
- Figure 62 - Neighbour RSSI 79
- 4.4.3 IP Routing 80
- 4.4.4 Radio Settings 81
- 4.4.5 Mesh Fixed Routes 82
- Example #1 83
- Example #2 84
- Writing Configuration File 87
- System Log File 87
- Reading Configuration File 87
- Figure 73 - Format USB 88
- Figure 74 - Quick Format 88
- Figure 75 - Firmware Files 88
- Figure 76- firmware version 89
- Product Reconfiguration 90
- Demonstration Mode 91
- Feature Licence Keys 91
- Chapter 5 - Diagnostics 92
- 5.1.1 Watchdog Error Log 93
- 5.2 Connectivity (WibMesh) 95
- 5.4 Neighbour RSSI (WibMesh) 97
- Figure 87 - Multipath Fading 98
- Trace Route 100
- 5.7 Monitor Comms 103
- Chapter 6 - Specifications 108
- “Output Coils” 112
- “Input Bits” 112
- “Input Registers” 113
- “Holding Registers” 114
- 115 116
- 118 119
- 119 120
- 120 121
- 121 122
- 122 123
- 123 124
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce