Weidmuller WI-I/O-9-U2: Wireless Mesh I/O & Gateway User Uživatelský manuál Strana 108
- Strana / 126
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
107
Chapter 6 - Specifications
6.1 Specifications
Radio Transceiver
Frequency
902–928MHz
(1)
;869.525MHz, 869.875MHz
(1)
Transmit power
1mW (+0dBm) to 1W (+30dBm)
(2)
1mW (+0dBm) to 500mW (+27dBm)
(3)
Transmission
Frequency Hopping Spread Spectrum (FHSS)
(2)
Single Fixed Frequency
(3)
Modulation
Frequency Shift Keying (FSK)
Receive Sensitivity
-109dBm @ 19.2kbps (3% FER)
(2)
-109dBm @ 14.4kbps (3% FER)
(3)
Channel Spacing
50 x 250KHz
(2, 4)
; Single 250KHz
(2, 4)
Radio data rate
19.2 – 115.2kbps
(1, 2)
; 14.4 – 76.8kbps
(1, 3)
Range (LOS)
Typically
32Km (20 mi.) @ 1W
(2,5)
; 10Km (6 mi.) @ 500mW
(3,5)
Antenna Connector
1 x Female SMA Standard Polarity
Input/Output
Discrete Input
8 Digital I/O (1 – 4 Configurable as Pulsed Input or Output)
On-State Voltage: <2.1Vdc
Wetting Current: 3.3mA
Max I/P Pulse Rate – DI 1/2: 50kHz, DI 3/4: 1kHz
Max I/P Pulse Width - DI 1/2: 10uSec, PI 3/4: 0.2mSec
Discrete Output
8 Digital I/O (1 – 4 Configurable as Pulsed Input or Output)
On-State Voltage – DO Max: <0.5v
Maximum Current: 200mA
Max O/P Pulse Rate – PO Max Rate: 1kHz
Analog Inputs
4 AI (2 Differential, 2 Single Ended)
Current Range: 0 – 24mA
Current Resolution: 14 Bits
Accuracy (Current): 0.1%
Voltage Input Range: AI 1/2: 0 – 20V, AI 3/4: 0 – 5V
Voltage Resolution: 14 Bits
Accuracy (Voltage): 0.1% full scale
Analog Output
2 AO (Sourcing)
Current Range: 0 – 24mA
Current Resolution: 13 Bits
Accuracy (Current): 0.1% (20uA)
Ethernet Ports
Ethernet Port
10/100baseT; RJ45 Connector – IEEE 802.3
Link Activity
Link, 100baseT via LED
Serial Ports
- Industrial Wireless MESH I/O 1
- WI-I/O 9-U2 MESH I/O 1
- 804.794.2877 Main 2
- 804.794.0252 Fax 2
- Industry Canada: 3
- FCC Notice: 4
- Hazardous Location Notices: 5
- IMPORTANT Notice: 6
- TABLE OF CONTENTS 7
- TABLE OF FIGURES 11
- Chapter 1 - Introduction 13
- 1.2 Module Structure 15
- 1.3 Getting Started 16
- Chapter 2 - Installation 17
- 2.2.2 Expansion I/O Supply 19
- 2.2.3 Internal I/O 20
- 2.2.4 Grounding 20
- 2.3 Radio 21
- 2.4 Antenna 22
- Yagi antennas 26
- 2.5 Connections 27
- WI-IO 9-U2 28
- “Factory Boot” switch 29
- USB Host port 29
- Dipswitches 29
- Front panel connections 30
- Figure 16 - Fail-Safe State 33
- 2.5.5 Analog Inputs 34
- Single Ended Voltage Inputs 36
- 2.5.6 Analog Outputs 37
- Chapter 3 - Operation 38
- Digital Inputs 39
- Digital Outputs 39
- ETHERNET 40
- LINK100M 40
- 3.3 System Design 41
- 3.3.4 Design for Failures 42
- Fail-to-transmit alarm 43
- Fail-to-receive alarm 43
- 3.4 WIBMesh 44
- Chapter 4 - Configuration 46
- Figure 23 – Network Settings 47
- Figure 24 - Ping 47
- Figure 26 - IP Gateway Mode 49
- Figure 27 - Default Gateway 49
- Figure 28 -IP Address Range 49
- Figure 29 - Routing Rule 50
- 4.3 Module Configuration 51
- Re-Open Previous Project 52
- 4.3.2 Configuration Screens 53
- 4.3.3 Project Screen 54
- 4.3.4 Adding Units 54
- Unit Details 55
- 4.3.5 Mappings 56
- Write Mapping 57
- Gather Scatter Mapping 57
- Read Mappings 57
- Example configuration 60
- 4.3.7 Address Map 61
- 4.3.9 I/O Configuration 62
- Pulsed Outputs 63
- Analog Inputs 64
- Analog Outputs 65
- Adding modules 65
- (selected on the rotary 66
- 4.3.11 Failsafe Blocks 67
- “Invalid” register state 68
- 4.3.12 Sensitivity Blocks 69
- 4.3.13 Serial Configuration 70
- Serial - Expansion I/O 71
- 4.3.14 Modbus Configuration 72
- Mapping parameters 73
- Modbus TCP Mapping Examples 75
- Modbus RTU Master 75
- Modbus RTU 76
- Master Example 76
- 4.4 Web based Configuration 77
- Figure 62 - Neighbour RSSI 79
- 4.4.3 IP Routing 80
- 4.4.4 Radio Settings 81
- 4.4.5 Mesh Fixed Routes 82
- Example #1 83
- Example #2 84
- Writing Configuration File 87
- System Log File 87
- Reading Configuration File 87
- Figure 73 - Format USB 88
- Figure 74 - Quick Format 88
- Figure 75 - Firmware Files 88
- Figure 76- firmware version 89
- Product Reconfiguration 90
- Demonstration Mode 91
- Feature Licence Keys 91
- Chapter 5 - Diagnostics 92
- 5.1.1 Watchdog Error Log 93
- 5.2 Connectivity (WibMesh) 95
- 5.4 Neighbour RSSI (WibMesh) 97
- Figure 87 - Multipath Fading 98
- Trace Route 100
- 5.7 Monitor Comms 103
- Chapter 6 - Specifications 108
- “Output Coils” 112
- “Input Bits” 112
- “Input Registers” 113
- “Holding Registers” 114
- 115 116
- 118 119
- 119 120
- 120 121
- 121 122
- 122 123
- 123 124
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.228 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce